CLA-206A 2-way Active Line Array Column - 2x6.5”LF + 1x1.4”HF - 600Wrms+300Wrms Stand-alone or as a part of the CLA 604.2A system, the CLA 206A 2 x 6.5" + 1 x 1.4" active cabinet excels for both SPL and audio articulation. Now making life easier for those on the road, both the CLA406.2A and more compact CLA206A have been designed with portability in mind, from the rugged hardware to new accessories which make set-up both extremely quick and highly intuitive. Bi-amplified 2-way line array 2 x 165mm (6.5 inches) custom woofers with 38mm (1.5 inch) coil Neodymium B&C compression HF driver with 36mm (1.4 inch) throat and 64mm (2.5 inch) coil Large format FBT waveguide with 100 H x 25 degrees V dispersion Frequency response from 65Hz to 20KHz Class-D 600Wrms for LF and 300Wrms for HF amplifiers with switching mode power supply DSP processor with 8 equalization presets Control panel with XLR input and link, volume, presets, filter-HP, ground-lift Neutrik PowerCON IN and LINK power connectors Cabinet in 12mm (0.5 inches) birch plywood with scratch-resistant varnish, two side handles, rubber inserts for protection, and anti-slip upper and lower 4 lateral inserts, two upper and two lower points designed to accept quick release pins or M10 screws. New hardware for flying installations, for ground setups, and the possibility of coupling two or more CLA 406A / CLA 206A with an angle of 0 - 20 degrees in 5-degree steps vertically, all with optional quick release pins for touring. The topside is inclined 20 degrees to have maximum flexibility of use in combination with other CLA 206A or CLA 406A in order to adapt the vertical dispersion angle of the system to the listening area. The system can be used both in small point source systems with the CLA 118SA sub and in clusters of two to have a dispersion of 40 degrees (V). It can also be considered a down-fill for CLA 406A systems. MORE»
| List | $2,780.00 |
2-way Active Line Array Column - 4x6” + 1.4” - 900Wrms, 133dB The Vertus CLA 406.2A comprises four custom 6.5" inch woofers with 1.5" voice coils and a 1.4-inch large format Neodymium compression driver with a 2.5-inch voice coil with a 100 H x 25 H degree dispersion. The built-in amp module delivers 600W for the LF section and 300W for HF for 133dB SPL Designed to be used with the CLA 118SA. FBT Vertus CLA 406.2A 2-way Active Line Array Column, the increased demand for an easy to set-up, sonically superior portable sound reinforcement system has prompted FBT to introduce a new version of the renowned VERTUS CLA460A active column array. The launch of the new VERTUS columns follows a steep rise in the use of the VERTUS CLA406A for mobile sound reinforcement applications and installation – a trend spurred on by the column’s depth of versatility and audio performance. Now making life easier for those on the road, both the CLA406.2A and more compact CLA206A have been designed with portability in mind, from the rugged hardware to new accessories which make set-up both extremely quick and highly intuitive. Bi-amplified 2-way line array 4 x 165mm (6.5 inches) custom woofers with 38mm (1.5 inches) coil Neodymium B&C compression HF driver with 36mm (1.4 inch) throat and 64mm (2.5 inch) coil Large format FBT waveguide with 100 degrees H x 25 degrees V dispersion Frequency response from 65Hz to 20KHz Class-D 600Wrms for LF and 300Wrms for HF amplifiers with switch mode power supply DSP processor with 8 equalization presets Control panel with XLR input and link, volume, presets, filter-HP, ground-lift Neutrik PowerCON IN and LINK power connectors Cabinet in 12mm (0.5 inches) birch plywood with scratch-resistant varnish, two side handles, rubber inserts for protection, and upper and lower anti-slip 4 lateral inserts, two upper and two lower points designed to accept quick release pins or M10 screws, and two rear M6 suspension points. New hardware for flying installations, for ground setups, and the possibility of coupling two or more CLA 406.2A / CLA 206A with an angle of 0 degree-20 degree in 5-degree steps vertically, all with optional quick release pins for touring. Topside inclined by 10 degrees to have maximum flexibility of use in combination with other CLA 406.2A or CLA 206A in order to adapt the vertical dispersion angle of the system to the listening area. The system can be used both in point source systems with the CLA 118SA sub and in vertical clusters, with the CLA 206A down-fill. MORE»
| List | $4,015.00 |
CLA-604-A 2-way Active Line Array Column - 6x4" - 400Wrms+100Wrms 125db SPL The Vertus CLA 604 Active Column Line Array has a 6 x 4” custom woofer with a 1” voice coil and 4 x 1” dome neodymium tweeter on a waveguide. The built-in amplifier delivers 400W + 100W RMS to achieve 125DB SPL Designed to work with the CLA 208SA Subs. Black Finish CLA604A is an extruded aluminum column speaker fitted with 6 x 4" custom woofers and 4 x 1" dome tweeters, each coupled to a waveguide. The internal Class D amplification, 400W for woofers and 100W for tweeters with switch mode power supply and DSP processor with 4 equalization presets provide unexpected dynamics in a system of these dimensions. The rapid latching system with pins allows for the expansion of the system, doubling-up CLA604A modules to form a unified column with an absolute and coherent source integration and increase of SPL and low-frequency directivity control. CLA system features: High-level sound quality from 50Hz to 20kHz expressly developed for live performance Long-distance sound projection and better SPL distribution toward the audience Great and dynamic power performance thanks to a tri-amplification system Lightweight and easy to carry Design and elegance for easy integration even in the most demanding installations Very compact dimensions enable the listener to concentrate on sound and not on speakers! High horizontal dispersion 2-Way Bi-Amped 6x 4" Neodymium woofer 4x 1" Neodymium tweeter with horn 400W Class D amplifier for the bass range 100W Class D amplifier for high frequencies Built-in switched-mode power supply DSP Processor with 4 equalizers presets Control panel with volume, presets, HP filter, mic/ line, status LED Aluminum housing (deep-drawn) Powder-coated surface Tripod or wall mountable Frequency range: 130 Hz - 20 kHz Max. SPL: 125 dB 100° x 20° XLR Signal and power twist for power input and output Dimensions: 130 x 841 x 130 mm Weight: 9 kg Color: Black or White MORE»
| List | $2,060.00 |
CLA-604-A-W 2-way Active Line Array Column - 6x4" White. 125db SPL The Vertus CLA 604 Active Column Line Array has a 6 x 4” custom woofer with a 1” voice coil and 4 x 1” dome neodymium tweeter on a waveguide. The built-in amplifier delivers 400W + 100W RMS to achieve 125DB SPL Designed to work with the CLA 208SA Subs. Black Finish CLA604A is an extruded aluminum column speaker fitted with 6 x 4" custom woofers and 4 x 1" dome tweeters, each coupled to a waveguide. The internal Class D amplification, 400W for woofers and 100W for tweeters with switch mode power supply and DSP processor with 4 equalization presets provide unexpected dynamics in a system of these dimensions. The rapid latching system with pins allows for the expansion of the system, doubling-up CLA604A modules to form a unified column with an absolute and coherent source integration and increase of SPL and low-frequency directivity control. CLA system features: High-level sound quality from 50Hz to 20kHz expressly developed for live performance Long-distance sound projection and better SPL distribution toward the audience Great and dynamic power performance thanks to a tri-amplification system Lightweight and easy to carry Design and elegance for easy integration even in the most demanding installations Very compact dimensions enable the listener to concentrate on sound and not on speakers! High horizontal dispersion 2-Way Bi-Amped 6x 4" Neodymium woofer 4x 1" Neodymium tweeter with horn 400W Class D amplifier for the bass range 100W Class D amplifier for high frequencies Built-in switched-mode power supply DSP Processor with 4 equalizers presets Control panel with volume, presets, HP filter, mic/ line, status LED Aluminum housing (deep-drawn) Powder-coated surface Tripod or wall mountable Frequency range: 130 Hz - 20 kHz Max. SPL: 125 dB 100° x 20° XLR Signal and power twist for power input and output Dimensions: 130 x 841 x 130 mm Weight: 9 kg Color: Black or White MORE»
| List | $2,060.00 |
CLA-604-W 2-way Passive Line array column - 6x4” + 4x1” - 500Wrms - 100°H x 20°V dispersion White RAL9016 The Vertus CLA 604 ActiveColumn Line Array has a 6 x 4” custom woofer with a 1” voice coil and 4 x 1” dome neodymium tweeter on a waveguide. The built-in amplifier delivers 400W + 100W RMS to achieve 125DB SPL Designed to work with the CLA 208SA Subs. High-level sound quality from 50Hz to 20kHz expressly developed for live performance Long-distance sound projection and better SPL distribution toward the audience Great and dynamic power performance thanks to the tri-amplification system Lightweight and easy to carry Design and elegance for easy integration even in the most demanding installations Very compact dimensions enable the listener to concentrate on sound and not on speakers! High horizontal dispersion 2-Way Bi-Amped 6x 4" Neodymium woofer 4x 1" Neodymium tweeter with horn 400W Class D amplifier for the bass range 100W Class D amplifier for high frequencies Built-in switched-mode power supply DSP Processor with 4 equalizers presets Control panel with volume, presets, HP filter, mic/ line, status LED Aluminum housing (deep-drawn) Powder-coated surface Tripod or wall mountable Frequency range: 130 Hz - 20 kHz Max. SPL: 125 dB 100° x 20° XLR Signal and power twist for power input and output Dimensions: 130 x 841 x 130 mm Weight: 9 kg Colour: White MORE»
| List | $1,545.00 |
CS-1000 Active Complete System - 12" subwoofer w/ Satellite 1000Wrms. Compact Line Array System 600W + 400W RMS -129 DB SPL Created as a no-compromise choice for both live performers and installers, the VERTUS CS1000 compact line array combines maximum performance with a modular, scalable approach. Its lightweight but sturdy construction blended with FBT’s distinctive engineering and elegance has delivered a system that can be deployed on stage within minutes, or discreetly integrated into the most delicate of decors to provide high-quality sound and controlled directivity. A bi-amplified design, the system comprises a long excursion 12” bass reflex subwoofer and a passive mounted satellite, linked via a Neutrik SPEAKON connector and equipped with six full-range neodymium 3” drivers. Onboard the subwoofer is a Class-D, two channel amplifier, complete with switch-mode power supply, delivering 600W RMS to the subwoofer and 400W RMS to the satellite, both of which are housed in birch plywood enclosures. For ease of use, a storage compartment is provided within the subwoofer enclosure to securely house both the satellite speaker and its supplied mounting pole for storage and transport. A dedicated locking system holds all of the equipment in place. MORE»
| List | $2,680.00 |
CS-1000-W Active Complete System - 12" subwoofer w/ Satellite 1000Wrms. 129 DB SPL - WHITE Created as a no-compromise choice for both live performers and installers, the VERTUS CS1000 compact line array combines maximum performance with a modular, scalable approach. Its lightweight but sturdy construction blended with FBT’s distinctive engineering and elegance has delivered a system that can be deployed on stage within minutes, or discreetly integrated into the most delicate of decors to provide high-quality sound and controlled directivity. A bi-amplified design, the system comprises a long excursion 12” bass reflex subwoofer and a passive mounted satellite, linked via a Neutrik SPEAKON connector and equipped with six full-range neodymium 3” drivers. Onboard the subwoofer is a Class-D, two channel amplifier, complete with switch-mode power supply, delivering 600W RMS to the subwoofer and 400W RMS to the satellite, both of which are housed in birch plywood enclosures. For ease of use, a storage compartment is provided within the subwoofer enclosure to securely house both the satellite speaker and its supplied mounting pole for storage and transport. A dedicated locking system holds all of the equipment in place. Modular design allows two systems to be configured as one single solution via optional accessories Bass reflex stackable subwoofer in a birch plywood enclosure with diecast aluminum handle and rubber inserts, plus M20 support and a custom pole-mount solution facilitating adjustable height and vertical aiming The satellite and pole are fully integrated into the subwoofer cabinet, where a push button system locks the satellite in place for transportation The satellite is equipped with a coupling system for accessories that allows the extension of the length of the line array, positioning one atop the other. Alternatively, the same system allows the satellite to be permanently wall-mounted. Ideal for both live applications and fixed installations Easily expandable to a total power of 8.000W peak (via a stereo system consisting of 4 x VERTUS CS1000, positioned two per side) MORE»
| List | $2,680.00 |
J-12 2-way PASSIVE speaker - 12" + 1" - 300Wrms The J12 is a passive speaker featuring a 12" Driver and a 1" Compression driver This Italian made speaker features a rugged gas injected molded polypropylene cabinet with Speakon connections and a standard 35mm pole mount *Available in Black or White 2-way passive sound reinforcement system Polypropylene enclosure 1 x 12" custom woofer 1 x 1" high-frequency driver 300W RMS recommended amplifier 150W long term power 600W short term power IEC 268-5 2 x M10 suspension points Internal passive crossover filter Input panel with 2 x Speakon NL4 Completely manufactured in Italy Applications: Band P.A. Personal monitor Small theatres Auditoriums Piano bar DJ Stage monitor Conference rooms Fixed installations in live clubs Pubs Gyms MORE»
| List | $720.00 |
J-12-A 2-way Active speaker - 12" + 1" - 350Wrms+100Wrms The J12a is an Active speaker featuring a 12" LF Driver and a 1" Compression driver This Italian-made speaker features a rugged gas injected molded polypropylene cabinet with a DSP processed amplifier delivering 350W + 100W RMS 128dB SPL and a standard 35mm pole mount. *Available in Black or White (12’’) custom woofer with improved efficiency and linearity (1”) HF custom compression driver 90°H x 60°V constant directivity horn 2-way bi-amplified system in Bass-Reflex 350Wrms class D amplifier for LF and 100Wrms for HF High-efficiency switch mode power supply On-board Digital Signal processing with dynamic equalizations and protections for high SPL and high reliability 4 DSP preset for maximum acoustical flexibility Polypropylene enclosure with integrated handle 2 x M10 anchoring points 35mm Internal top hat Net weight 13.7kg Net dimensions 410x663x387mm (W/H/D) Applications: Band P.A. Personal monitor Small theatres Auditoriums Piano bar DJ Stage monitor Conference rooms Fixed installations in live clubs Pubs Gyms *Available in Black or White MORE»
| List | $1,030.00 |
J-12-W 2-way PASSIVE speaker - 12" + 1" - 300Wrms in WHITE The J12 is a passive speaker featuring a 12" Driver and a 1" Compression driver This Italian-made speaker features a rugged gas injected molded polypropylene cabinet with Speakon connections and a standard 35mm pole mount. *Available in Black or White MORE»
| List | $720.00 |
J-8 2-way PASSIVE speaker - 8" + 1" - 160Wrms The J8 is a passive speaker featuring an 8" Driver and a 1" Compression driver This Italian-made speaker features a rugged gas injected molded polypropylene cabinet and Speakon connections with a smaller 25mm pole mount. *Available in Black or White The 2-way passive sound reinforcement system Polypropylene enclosure 1 x 8" custom woofer 1 x 1" high-frequency driver 160W RMS recommended amplifier 80W long term power 320W short term power IEC 268-5 2 x M6 suspension points Internal passive crossover filter Input panel with 2xSpeakon NL4 Available in white color Completely manufactured in Italy 96.5dB Sensitivity APPLICATION: Band P.A. Personal monitor Small theatres Auditoriums Piano bar DJ Stage monitor Conference rooms Fixed installations in live clubs Pubs Gyms MORE»
| List | $620.00 |
J-8-A 2-way Active speaker - 8" + 1" - 200Wrms+50Wrms The J8 is a passive speaker featuring an 8" Driver and a 1" Compression driver This Italian-made speaker features a rugged gas injected molded polypropylene cabinet and Speakon connections with a smaller 25mm pole mount. *Available in Black or White The 2-way passive sound reinforcement system Polypropylene enclosure 1 x 8" custom woofer 1 x 1" high-frequency driver 160W RMS recommended amplifier 80W long term power 320W short term power IEC 268-5 2 x M6 suspension points Internal passive crossover filter Input panel with 2xSpeakon NL4 Available in white color Completely manufactured in Italy 96.5dB Sensitivity APPLICATION: Band P.A. Personal monitor Small theatres Auditoriums Piano bar DJ Stage monitor Conference rooms Fixed installations in live clubs Pubs Gyms MORE»
| List | $875.00 |
J-8-A-W 2-way Active speaker - 8" + 1" - 200Wrms + 50Wrms. White RAL9016 The J8A is an Active 200 Watts + 50 Watts speaker featuring an 8" Driver and a 1" Compression Driver. This Italian-made speaker features a rugged gas-injected molded polypropylene cabinet with a smaller 25mm pole mount. * Available in Black or White Applications: Band P.A. Personal monitor Small theatres Auditoriums Piano bar DJ Stage monitor Conference rooms Fixed installations in live clubs Pubs Gyms MORE»
| List | $875.00 |
J-8-W 2-way PASSIVE speaker - 8" + 1" - 160Wrms. White RAL9016 The J8 is a passive speaker featuring an 8" Driver and a 1" Compression driver This Italian-made speaker features a rugged gas injected molded polypropylene cabinet and Speakon connections with a smaller 25mm pole mount. *Available in Black or White The 2-way passive sound reinforcement system Polypropylene enclosure 1 x 8" custom woofer 1 x 1" high-frequency driver 160W RMS recommended amplifier 80W long term power 320W short term power IEC 268-5 2 x M6 suspension points Internal passive crossover filter Input panel with 2xSpeakon NL4 Available in white color Completely manufactured in Italy 96.5dB Sensitivity APPLICATION'S: Band P.A. Personal monitor Small theatres Auditoriums Piano bar DJ Stage monitor Conference rooms Fixed installations in live clubs Pubs Gyms MORE»
| List | $620.00 |
JMAXX-110A 10-inch, Professional 2-way Active Speaker - 10" + 1" - 700Wrms+200Wrms The JMaxX 110A features a 10" LF woofer with 2" voice coil 1 exit throat HF compression driver with 1 voice coil 700W RMS LF, 200W RMS HF DSP with 4-EQ pre-sets all in an incredibly lightweight gas injected molded polypropylene cabinet. 129.5 dB SPL. 10 " LF woofer and a 1’’ exit throat HF compression driver with 1.4” voice coil 700W RMS Low Frequency AND 200W RMS for High Frequency, Class D power amplifiers with switch mode power supply DSP with 4-EQ presets Control panel with XLR IN and XLR LINK, Volume, EQ presets, HP filter, GND LFT switch 2 x M10 suspension points, 35mm (1.3/8”) top-hat speaker stand socket, wall bracket mount flange plate 90°H x 60°V constant directivity horn Stage monitor angling facility with 12°, 40°, or 55° taper MORE»
| List | $1,100.00 |
JMAXX-112A 12-inch, Professional 2-way Active Speaker. The JMaxX 112A features a 12" LF woofer with 2" voice coil 1" exit throat HF compression driver with 1" voice coil 700W RMS LF, 200W RMS HF DSP with 4-EQ pre-sets all in an incredibly lightweight gas injected molded polypropylene cabinet. 131 dB SPL. 12 Inch Low Frequency Woofer and a 1" High frequency Compression driver 2-way, bi-amplified bass reflex design cabinet 700W RMS LF, 200W RMS HF, Class D power amplifiers with switch mode power supply DSP with 4-EQ presets Control panel with: XLR IN and XLR LINK, Volume, EQ presets, HP filter, GND LFT switch 2 x M10 suspension points, 35mm (1.3/8”) top-hat speaker stand socket, wall bracket mount flange plate 90° Horizontal x 60° Vertical constant directivity horn Stage monitor angling facility with 12°, 40° or 55° taper Just 13.8 Kg MORE»
| List | $1,235.00 |
JMAXX-114A 14-inch, Professional 2-way Active Speaker The JMaxX 114A features a 14" LF woofer with 2" voice coil 1" exit throat HF compression driver with 1.4" voice coil 700W RMS LF, 200W RMS HF DSP with 4-EQ pre-sets all in an incredibly lightweight gas injected molded polypropylene cabinet. 132 dB SPL. 30.86 lbs MORE»
| List | $1,140.00 |
Passive Line Array - 2x6,5" + 1,4" - 500Wrms+150Wrms The FBT MITUS 206L is a two-way compact line array system featuring 2 x 6.5” B&C neodymium woofers with a 1.7” voice coil and a 1.4” exit B&C neodymium driver with a 2.5” voice coil. All in a Polypropylene gas-injected enclosure. 500W + 150W - 16ohm 129dB SPL LF / 133dB SPL HF Compact 2-way, bass-reflex design Passive version, recommended amplifier of 500Wrms / 16ohm LF and 150 Wrms / 16ohm HF Internal HF protection Neutrik Speakon NL- 4MDV connectors IN & LINK OUT External digital processor require 2 x 6.5’’ (165 mm) B&C neodymium woofers with 1.7’’ (44 mm) coil 1.4’’ (36 mm) exit B&C neodymium driver with 2.5’’ (64 mm) coil Frequency response from 75Hz to 20KHz 100° horizontal waveguide with very low distortion and near-flat wavefront up to 18Khz High impact polypropylene gas-injected enclosure with integrated rigging hardware adjustable with 0° to 10° angle between cabinets at 2° step Ideal for small to medium-sized applications, from single pole-mounted loudspeakers with 100°H x 10°V coverage to multiple cabinet full sized line arrays, the MITUS 206L may be used also in outdoor applications where the system is not directly exposed to the elements A wide range of hardware accessories for flying and ground-stacked configurations Very lightweight, only 13.5Kg MORE»
| List | $1,955.00 |
MITUS-206-LA Active line array - 2x6,5" + 1,4" - 600Wrms+300Wrms The FBT MITUS 206LA is a compact lightweight two-way design incorporating 2 x 6.5” B&C neodymium woofers with a 1.7” voice coil and a 1.4” B&C neodymium driver with a 2.5” voice coil. The modularity of the FBT MITUS 206LA makes it extremely flexible for a wide range of applications, from a small 2 cabinet P.A. system to an elaborate line array system consisting of up to 12 MITUS 206LA cabinets along with multiple FBT MITUS 212FSA subs for large concert events. Frequency response from 68Hz to 20KHz Latest Class D built-in amplifiers, 600Wrms to the LF and 300Wrms to the HF with switch mode power supply DSP on-board with 8 presets, +/- 5db HF level control for accurate amplitude shading Control panel with XLR input and link, volume, presets, HF level, HP-filter, ground-lift 100° horizontal waveguide with very low distortion and near-flat wavefront up to 18Khz High impact polypropylene gas-injected enclosure with integrated rigging hardware adjustable with 0° to 10°angle between cabinets at2° step Ideal for small to medium-sized applications, from single pole-mounted loudspeakers with 100°H x 10°V coverage to multiple cabinet full-sized line array, the MITUS 206LA may be used also in outdoor applications where the system is not directly exposed to the elements A wide range of hardware accessories for flying and ground-stacked configurations MORE»
| List | $2,470.00 |
MITUS-212-FS Flyable Passive Subwoofer - 2x12" - 1000Wrms The FBT MITUS 212FS is a passive 2 x 12" B&C with a 3" Voice coil compact and flyable subwoofer. When combined together in a ground-stacked or flying array it extends the low frequencies of the MITUS 206L line array system. The FBT MITUS 212FS is a 2 x 12" compact and flyable subwoofer which can extend the low frequencies of the MITUS 206L when combined together in ground-stacked or flying arrays. The modularity of the FBT MITUS 212FS makes it extremely flexible for a wide range of applications, from a small system to an elaborate line array system consisting of up to 12 MITUS 206L cabinets along with multiple FBT MITUS 212FS subs for large concert events. The FBT MITUS 212FS shall meet the following performance criteria: Frequency response of 50Hz to 250Hz,Frequency sensitivity of 99dB, Maximum SPL of 134dB continuous and 138dB peak, Recommended power amplifier 1000W RMS/8 Ohm. The MITUS 212FS feature Baltic birch plywood construction covered in a scratch-resistant black paint with an M20 top-mounted stand adapter. Input connectors shall be parallel wired Neutrik NL4 Speakon. 1000W -138dB SPL MORE»
| List | $3,090.00 |
MITUS-212-FSA Processed Flyable Active Subwoofer - 2x12" - 1200Wrms. The FBT MITUS 212FSA is an Active 2 x 12" B&C with a 3" Voice coil compact and a flyable subwoofer that can extend the low frequencies of the MITUS 206L when combined together in ground-stacked or flying arrays. Built-in amplifier Delivering 1200W – 138dB SPL It can also be utilized as a flyable "Mid-Sub" extension when paired with the Mitus 206LA active line array, and an additional subwoofer. Compact vented subwoofer sharing the same width and suspension hardware as the MITUS 206L 320 mm (2 x 12’’) B&C neodymium magnet high excursion subwoofers with 75 mm (3’’) voice coils Frequency Response from 50Hz to 120Hz Neutrik Speakon NL- 4MDV connectors IN & LINK OUT External digital processor required 15 mm (5/8’’) birch plywood enclosure, scratch-resistant black paint Low-frequency extension cabinet for the MITUS 206L line array for flying or ground-stacked configurations. M20 top mount stand socket MORE»
| List | $3,865.00 |
MUSE-210-L Passive line array - 2x10"LF + 2x1''HF- 600Wrms+300Wrms 2-way, compact bass-reflex line array system Two 250mm (10”) woofers with 64mm (2.5”) voice coils Two custom B&C HF compression drivers with 25mm (1”) throats Precision waveguide delivering 90° of horizontal dispersion up to 18Khz Frequency response from 55Hz to 20KHz Control panel with XLR input and link, preset control, HF level control, HP-filter, and ground lift Strong birch plywood cabinet with integrated aluminum handles, hardware, and fly-ware offering adjustable angling ranging from 0° to 10° in 2° increments Wide range of accessories to offer ultimate flexibility no matter whether your MUSE line array system is suspended or ground-stacked, plus a specially designed cover to guard against bad weather. MORE»
| List | $3,915.00 |
MUSE-210LAV Compact Bass reflex Active line array - 2 x 10" + 2 x 1" 600Wrms+300Wrms Each modular MUSE element comprises two 250mm (10") custom-designed woofers with 64mm high excursion voice coils and two custom B&C HF compression drivers with 25mm (1") throat. The waveguide, optimized via a series of simulations using BEM finite elements to eliminate distortion, boasts a horizontal dispersion of 90°. It has been designed to present an optimum load to the driver's diaphragm at 800Hz, thereby allowing the propagation of an acoustic wave in the horizontal field up to 18kHz. The resulting enclosure can contend with even the most challenging of physical environments, delivering an ideal cylindrical source, while the acoustic configuration of the central horn offers a particularly linear and symmetric horizontal dispersion. MORE»
| List | $4,530.00 |
MUSE-210LN Active line array - 2x10" + 2x1"- 800Wrms+400Wrms - INFINITO The MUSE 210 LN is our newest, most advanced line array. Building on the legendary MUSE 210 LA and adding new, advanced amplifier technology, and network control via our incredible Infinito software. It has 2 x 10" woofers and 2 x 1" B&C custom HF drivers. The waveguide is optimized to minimize distortion and has a horizontal dispersion of 90°. The acoustic configuration with the central horn allows for a particularly linear and symmetrical horizontal dispersion. The cabinet is made of 15mm birch plywood with two die-cast aluminum handles. The hardware integrated into the cabinet allows the suspension of 16 boxes with an inclination from 0° to 10° at a step of 1°. The design of the system is optimized for easy set-up, which makes it particularly suitable for musical touring acts. However, the aesthetic elegance also makes it suitable for fixed installations. The pinnacle of the entire project is the 800+400W RMS amplification module with a TCP/IP network interface. Based on the OCA ALLIANCE AES70 standard, it communicates with the ‘INFINITO system management suite remote control software. INFINITO is a true revolution in the FBT world that enhances the user experience, reaching new heights in terms of performance and simplicity! It is a software platform that is fully developed in-house by the FBT R&D team that offers real-time monitoring of the internal sensors and the status of the connected devices, fast IN/OUT Vu-meters, controls of all the parameters, group management, and warnings readout. The module is contained in an aluminum chassis with intelligent forced ventilation and is equipped with an OLED display with an encoder for parameter setting, among which 8 presets offer easy configuration, adapting the DSP to the curvature of the array and to the number of elements used. MORE»
MUSE-210LND Active line array - 2x10" + 2x1"- 800Wrms+400Wrms - INFINITO The MUSE 210 LND is our newest, most advanced line array. Building on the legendary MUSE 210 LA and adding new, advanced amplifier technology, and network control via our incredible Infinito software. It has 2 x 10" woofers and 2 x 1" B&C custom HF drivers. The waveguide is optimized to minimize distortion and has a horizontal dispersion of 90°. The acoustic configuration with the central horn allows for a particularly linear and symmetrical horizontal dispersion. The cabinet is made of 15mm birch plywood with two die-cast aluminum handles. The hardware integrated into the cabinet allows the suspension of 16 boxes with an inclination from 0° to 10° at a step of 1°. The design of the system is optimized for easy set-up, which makes it particularly suitable for musical touring acts. However, the aesthetic elegance also makes it suitable for fixed installations. The pinnacle of the entire project is the 800+400W RMS amplification module with a TCP/IP network interface. Based on the OCA ALLIANCE AES70 standard, it communicates with the ‘INFINITO system management suite remote control software as well as Dante, 24BIT 48-96KHz TCP/IP audio streaming. INFINITO is a true revolution in the FBT world that enhances the user experience, reaching new heights in terms of performance and simplicity! It is a software platform that is fully developed in-house by the FBT R&D team that offers real-time monitoring of the internal sensors and the status of the connected devices, fast IN/OUT Vu-meters, controls of all the parameters, group management, and warnings readout. The module is contained in an aluminum chassis with intelligent forced ventilation and is equipped with an OLED display with an encoder for parameter setting, among which 8 presets offer easy configuration, adapting the DSP to the curvature of the array and to the number of elements used. MORE»
MYRA 214L Passive Bi-amped 3way Line Array - 2 x 14" + 2 x 1.4" - 1600W rms + 640W rms MYRA system is a complete solution for mid to large-size touring applications and high-end fixed installations. MYRA 214L is a full-range variable curvature 3-WAY line array module. Designed without compromise, the MYRA establishes a new reference for SPL to size ratio, directivity control, coherence, and ease of use. It’s the result of an extensive three-year R&D program started from scratch to address the challenges of rental companies, FOH, and tour sound engineers. The heart of the 214L line array element features two uniquely designed neodymium coaxial compression drivers that combine 4-inch VC mid-frequency and 2.5-inch VC high-frequency into a 1.4" throat, developed in cooperation with B&C, and covering the 400Hz to 20kHz range. MORE»
PROMAXX114A Active 2-way composite enclosure with 14" & 1.4" 700w (class D) & 200w (AB) The ProMax114a is an active speaker equipped with a 14' custom FBT speaker complete with a 1.4" B&Cs compression driver 900w RMS HF - 90°H x 60°V dispersion - Designed, Engineered, and Manufactured in Italy. 2-way, bi-amplified, bass-reflex design cabinet Biamped: 700W RMS LF, 200W RMS HF, power amplifiers in Class D for LF and in Class H/AB for HF with switch-mode power supplies Digital signal processor with graphic display Control Panel features balanced XLR/Jack input, XLR LINK OUT, 2 x Volume, RCA Stereo input, DSP display with rotative encoder and push 2 x M10 suspension points, 35 mm (1,3/8”) top-hat speaker stand socket, wall bracket mount flange plate 90°H x 60°V constant directivity horn Front of House or Stage Floor Monitor: with 12°, 40° and 55° monitoring angles 3550mm (14") LF woofer with 64mm (2.5") voice coil, custom made for FBT 35mm (1.4") throat exit B&C HF magnet compression driver with 34mm (1.4”) voice coil Frequency response from 45Hz to 20KHz Sturdy, gas-injected polypropylene molded enclosures, engineered to contain undesired resonance Extremely light only 17.4kg Compact Dimensions: ProMaxX 114A uses the same size gas-injected polypropylene molded enclosure as the ProMaxX 112A, but features our 14” LF Woofer for lower frequency SPL. MORE»
| List | $2,060.00 |
The StageMaxX 12 MA is a Processed Active Reinforcement Stage Monitor. Featuring a 400W + 100W RMS amp module delivering 130dB SPL. Inside we have a Coaxial custom FBT 12” B&C speakers with 64mm (2.5”) voice coil with a B&C 25mm (1”) exit throat compression driver and 44mm (1.7”) voice coil, outside we have a Sturdy gas-injected polypropylene molded enclosure to avoid undesired resonance. All are proudly made in Italy. Black finish. The 4 presets are: ORIGINAL: is the typical “MaxX” sound adapted to the “STAGE” application HI-CUT / DRUM FILL: provides less mid-high for comfortable listening in near-field at a high level LO-CUT / DOUBLE: provides less low frequency for better intelligibility and for optimal coupling in a stereo configuration FOH: Front Of House use in suspended or pole-mount installations. FBT’s new StageMaxX 12Ma has been inspired by the need to have a product specifically designed and engineered for use as a stage monitor, overcoming all these compromises for full user satisfaction. Low profile and aesthetic elegance Compact size Frequency response studied for stage monitor applications High headroom before feedback High sound quality Great power and dynamics Symmetric dispersion Aligned LF and HF acoustic centers Easy handling on stage Lightweight Heavy-duty polypropylene cabinet MORE»
| List | $2,060.00 |
The StageMaxX 12 MA is a Processed Active Reinforcement Stage Monitor. Featuring a 400W + 100W RMS amp module delivering 130dB SPL. Inside we have a Coaxial custom FBT 12” B&C speakers with 64mm (2.5”) voice coil with a B&C 25mm (1”) exit throat compression driver and 44mm (1.7”) voice coil, outside we have a Sturdy gas-injected polypropylene molded enclosure to avoid undesired resonance. All are proudly made in Italy. White finish. The 4 presets are: ORIGINAL: is the typical “MaxX” sound adapted to the “STAGE” application HI-CUT / DRUM FILL: provides less mid-high for comfortable listening in near-field at a high level LO-CUT / DOUBLE: provides less low frequency for better intelligibility and for optimal coupling in a stereo configuration FOH: Front Of House use in suspended or pole-mount installations. FBT’s new StageMaxX 12Ma has been inspired by the need to have a product specifically designed and engineered for use as a stage monitor, overcoming all these compromises for full user satisfaction. Low profile and aesthetic elegance Compact size Frequency response studied for stage monitor applications High headroom before feedback High sound quality Great power and dynamics Symmetric dispersion Aligned LF and HF acoustic centers Easy handling on stage Lightweight Heavy-duty polypropylene cabinet MORE»
| List | $2,060.00 |
VENTIS-108 2-way Passive speaker - 8" + 1" - 250Wrms Ventis 108 is part of the Ventis range which is ideal for portable performance or fixed installation. This Passive speaker Features an 8" woofer and a 1" exit 1.4"VC compression driver. The recommended amplifier of 250 Watts at 8 Ohm will deliver 126dB SPL. Connections via 2x Speakon NL4 In + Thru. All are housed in a 15mm Baltic birch ply cabinet with a 35mm pole mount and a full-length grille. Optional brackets for installation are available. MORE»
| List | $1,080.00 |
VENTIS-110 2-way Passive speaker - 10" + 1" - 300Wrms. Ventis 110 is part of the Ventis range which is ideal for portable performance or fixed installation. This passive speaker Features a 10" woofer and a 1" exit 1.4"VC compression driver. Recommended amplifier of 300 W at 8 Ohm will deliver 127dB SPL connections via 2 x Speakon NL4 In + Thru. All are housed in a 15mm Baltic birch ply cabinet with a 35mm pole mount and a full-length grille. optional brackets for installation are available. MORE»
| List | $1,340.00 |
VENTIS-110A 10" 2-way Active speaker - 10" + 1" 700w + 200w w/DSP and Delay. Ventis 110A is part of the Ventis range which is ideal for portable performance or fixed installation. This Active speaker includes a 10" woofer and a 1" exit 1.4"VC compression driver.The built-in DSP LCD screened Amp module is 700W + 200W Delivering 131dB SPL. Features a 15mm Baltic birch ply cabinet with a 35mm pole mount and a full-length grille. optional brackets for installation are available. The FBT VENTIS range offers powerful DSP with 6 versatile presets. Crafted by expert FBT engineers, the presets offer a performance for every requirement. ORIGINAL / LIVE The renowned, smooth FBT sound VOCAL A special EQ setting to maximize speech intelligibility DJ is Designed to keep the energy high and your audience dancing TOURING The reliability and the roar of the industry’s most popular touring systems LOUDNESS The ultimate preset for listening at a medium or low volume WARM A special setting to emphasize full-bodied, low-mid frequencies 2-way, bi-amplified, bass-reflex design Bi-amped: 700W RMS LF and 200W RMS HF power amplifiers in Class D for LF and in Class H/AB for HF Digital Signal Processor with graphic display 15 mm (0.59") birch plywood scratch resistant enclosure and internal bracing High-efficiency switch mode power supply Control Panel features balanced XLR/Jack input, XLR LINK OUT, 2 x Volume, RCA Stereo input, DSP display with rotative encoder and push 250mm (10") LF woofer with 50mm (2") voice coil, custom made for FBT 25mm (1") exit throat B&C HF compression driver with 36mm (1.4") voice coil Frequency response from 58Hz to 20 kHz 80°H x 50°V Constant Directivity Rotatable Horn 6 x M10 suspension points, optional wall bracket mount thread, 35mm (1 3/8") top-hat Speaker stand socket, one aluminum handle 45° monitor taper Adjustable delay between 0 - 10m Weight: 15.6Kg Dimensions : 329 x 575 x 325mm MORE»
| List | $2,060.00 |
VENTIS 110AW 10" 2-way Active speaker - 10" + 1" w/DSP and Delay - White Ventis 110A is part of the Ventis range which is ideal for portable performance or fixed installation. This Active speaker includes a 10" woofer and a 1" exit 1.4"VC compression driver.The built-in DSP LCD screened Amp module is 700W + 200W Delivering 131dB SPL. Features a 15mm Baltic birch ply cabinet with a 35mm pole mount and a full-length grille. optional brackets for installation are available. The FBT VENTIS range offers powerful DSP with 6 versatile presets. Crafted by expert FBT engineers, the presets offer a performance for every requirement. ORIGINAL / LIVE The renowned, smooth FBT sound VOCAL A special EQ setting to maximize speech intelligibility DJ is Designed to keep the energy high and your audience dancing TOURING The reliability and the roar of the industry’s most popular touring systems LOUDNESS The ultimate preset for listening at a medium or low volume WARM A special setting to emphasize full-bodied, low-mid frequencies 2-way, bi-amplified, bass-reflex design Bi-amped: 700W RMS LF and 200W RMS HF power amplifiers in Class D for LF and in Class H/AB for HF Digital Signal Processor with graphic display 15 mm (0.59") birch plywood scratch resistant enclosure and internal bracing High-efficiency switch mode power supply Control Panel features balanced XLR/Jack input, XLR LINK OUT, 2 x Volume, RCA Stereo input, DSP display with rotative encoder and push 250mm (10") LF woofer with 50mm (2") voice coil, custom made for FBT 25mm (1") exit throat B&C HF compression driver with 36mm (1.4") voice coil Frequency response from 58Hz to 20 kHz 80°H x 50°V Constant Directivity Rotatable Horn 6 x M10 suspension points, optional wall bracket mount thread, 35mm (1 3/8") top-hat Speaker stand socket, one aluminum handle 45° monitor taper Adjustable delay between 0 - 10m Weight: 15.6Kg Dimensions : 329 x 575 x 325mm MORE»
| List | $2,060.00 |
VENTIS-112 2-way Passive speaker - 12" + 1" - 400Wrms. Ventis 112 is part of the Ventis range which is ideal for portable performance or fixed installation. This passive speaker Features a 12" woofer and a 1" exit 1.4" compression driver. The recommended amplifier of 400 W at 8 Ohm will deliver 129 dB SPL connections via 2x Speakon NL4 In + Thru. All are housed in a 15mm Baltic birch ply cabinet with a 35mm pole mount and a full-length grille. optional brackets for installation are available. MORE»
| List | $1,650.00 |
VENTIS-112A 12" 2-Way Active speaker 12" + 1" 700w + 200w w/DSP and Delay. Ventis 112A is part of the Ventis range which is ideal for portable performance or fixed installation. This Active speaker includes a 12" woofer and a 1" exit 1.4"VC compression driver.The built-in DSP LCD screened Amp module is 700W + 200W Delivering 133dB SPL. Features a 15mm Baltic birch ply cabinet with a 35mm pole mount and a full-length grille. optional brackets for installation are available. The FBT VENTIS range offers powerful DSP with 6 versatile presets. Crafted by expert FBT engineers, the presets offer a performance for every requirement. ORIGINAL / LIVE The renowned, smooth FBT sound VOCAL A special EQ setting to maximize speech intelligibility DJ is Designed to keep the energy high and your audience dancing TOURING The reliability and the roar of the industry’s most popular touring systems LOUDNESS The ultimate preset for listening at a medium or low volume WARM A special setting to emphasize full-bodied, low-mid frequencies. 2-way, bi-amplified, bass-reflex design Bi-amped: 700W RMS LF and 200W RMS HF power amplifiers in Class D for LF and in Class H/AB for HF Digital Signal Processor with graphic display 15 mm (0.59") birch plywood scratch resistant enclosure and internal bracing High-efficiency switch mode power supply Control Panel features balanced XLR/Jack input, XLR LINK OUT, 2 x Volume, RCA Stereo input, DSP display with rotative encoder and push 320mm (12") LF woofer with 64mm (2.5") voice coil, custom made for FBT 25mm (1") exit throat B&C HF compression driver with 36mm (1.4") voice coil Frequency response from 48Hz to 20 kHz 80°H x 50°V Constant Directivity Rotatable Horn 6 x M10 suspension points, optional wall bracket mount thread, 35mm (1 3/8") top-hat Speaker stand socket, two aluminum handles 45° monitor taper Adjustable delay between 0 - 10m Weight: 20.6Kg Dimensions : 387 x 665 x 380mm MORE»
| List | $2,320.00 |
VENTIS-112-M 2-way Passive monitor - 12" + 1" - 500Wrms The Ventis 112M is a dedicated floor monitor for use on small to medium-sized stages This passive speaker features a 12" coaxial custom woofer with a 2,5" voice coil and 1" exit throat B&C with a 1,7" voice coil. The rear panel provides two NL4 Neutrik Speakon connectors. Recommended amplifier 500W/8ohm will deliver 129dB SPL. Optional brackets for installation are available. MORE»
| List | $1,700.00 |
